Kyle Rankin @kyle@librem.one

5. Tying Threaded Groups Together

After threading a "round" number of heddles based on WPI or natural end of a pattern, I tie them with a temporary knot to separate from other groups.

This protects me against losing track of where I am in my threading, as I can always count the number of tied bundles.

This also protects against mistakes when sleying the reed, as I only deal with "round" numbers of threads at a time.

#weaving

4. Staggered Heddles When Threading

I, at most, separate only four heddles at a time from the rest when threading, and I stagger them in the order they are to be threaded so there is visible distance between them.

This not prevents threading mistakes, I can visually see the current 4-thread pattern in order and confirm where I am when threading a long complicated pattern.

#weaving

3. Unique Heddles

When threading your loom, it's easy to mix up a heddles from different harnesses as you are often only relying on depth perception.

I have a 4 harness loom with metal heddles. When buying more heddles for a rug project, I bought a different style, and then set up odd harnesses with one style and even with the other. This helps me catch threading mistakes as each harness is distinct from its neighbor.

#weaving

2. Maintaining the Cross

Lease sticks maintain your cross while dressing the loom to prevent counting mistakes when threading, but many instructions have you remove them after threading, I (like some Scandinavian weavers) leave them on to the end of the project.

This saved me in this project when I notice threading mistakes after I start to weave, and when a warp thread was missing entirely.

#weaving

1. Measuring Warp

When measuring warp I literally say the count over and over as a mantra as I run a thread the length of the warping board.

I always use a counting thread so I don't have to count the full number of warp threads, only smaller values (typically 10 or 12). This also means when I inevitably get distracted and lose count, I only count the warp threads on the outside of the counting thread.

#weaving

Weaving takes patience and attention to detail, at least if you want fabric that matches your plans. Mistakes are inevitable and you either accept them in the work or possibly spend hours correcting them.

All it takes is a distraction to lose where you were. Ideally you catch mistakes as soon as possible so there's less work to undo/redo. In this thread I'll describe some of my practices that help me catch errors.

#weaving

The second attempt is looking good for this 3D printed case for my knitting clock. Along with fixing some mistakes in my design, I also modified it so that it could print for the most part without supports. There was one area where that was unavoidable, so I added in basic supports. While there is a little cleanup where it bridged there, it's much less than I saw when I enabled internal supports in the first print.

#3dprinting

See if you can spot the treadling errors! I managed to make the same mistake three different times in pattern repeats so far. Combined with the threading mitsake from earlier, this is rapidly becoming the "warm up" towel where I hopefully get all of the mistakes out of my system before the next two.

#weaving

I had to cancel the print. There were a few flaws in the model that I couldn't ignore and that I wasn't able to see in the model itself. In particular the button mounting brackets were not attached to the sides of the case but just floating 1mm from the case. Rookie mistakes.

It's ok. This will allow me to make a few other refinements that I noticed when printing, but that weren't important enough by themselves to cancel it.

#3dprinting

We are 40 hours in and the structure that holds the knitting machine itself is completed. All that is left are the walls which also have button and motor mounts in them.

#3dprinting #knitting #electronics

After almost 16 hours, the case for my knitting clock is starting to take shape. You can now make out the central structure that will hold the knitting machine itself in place. While I tried to reduce overhangs, due to the nature of this model there still are quite a few so there will be a lot of internal support material to remove when this is done.

#3dprinting #knitting #electronics

I've been quiet about my hackaday-inspired knitting clock project ever since I decided to replace the 48-hook machine with a 22-hook model, but that's because I've been busy learning 3D modeling!

I realized the new 22-hook knitting machine fits on my 3D printer bed, so instead of a wooden case, I designed a custom case for it using Tinkercad. I just started an epic 2 day, 8-hour print of the case that takes up my entire print bed!

#3dprinting #knitting #electronics

In case anyone new to weaving is wondering how you recover from a mistake like this, measure out a new warp thread, thread it through the reed and heddle, and then hang it off of the back of the loom with a weight. I wrap the end of the warp around the weight until it hangs properly, and unwind it a bit every few times I advance the warp.

Then wrap the other end around a pin and pin it to the fabric. After enough rows eventually tension will keep it in place.

After weaving quite a few inches into the towel I thought something looked off and discovered I was missing a thread!

If you find the pin in the picture you can see that part of the pattern just looks a bit off. Follow that line up to where the thread finally is threaded and you can see where the pattern got corrected after I added a new warp thread.

#weaving

I finished tying on the new warp to the old and have started weaving the first of three towels. Beyond the different colored yarn, I also modified this design in two ways, taking advantage of the reversible nature of this doubleweave overshot pattern:

1. Since there is no "right" side to this, I reversed the color for almost 2/3 of the hem at the bottom so when I fold it, it matches the color on its own side.

2. I extended the inverted color of the pattern stripe.

#weaving #Fiberuary

Halfway through tying a new warp onto the remnants of the old. Wow this is tedious work, and there is at least 3 more hours to go, but I still think it is faster and less error-prone than re-threading it.

#weaving #Fiberuary