Let's brew a Bock! I'm using a Grainfather brewing system, essentially a giant computerized electric kettle with an integrated mash tun and a pump at the bottom. The process is similar to when I brewed with a big pot on a stove and a modified cooler for mashing, just automated.

Step one, add the "strike water" (what we steep the grain in) and heat it to 68C, the temperature we need to "mash" the grain (essentially steep it like with tea).

Show thread

As the water heats up I drop in the mash tun insert. It has a perforated bottom that prevents most of the grain from getting through, and it plus the barley husks in my mash ultimately act as a filter so only liquid gets through as we recirculate it.

Show thread

Now we add our pre-crushed malted barley to the water a bit at a time, stirring in between. This process is called "douging in" and you are basically making a giant barley porridge.

Show thread

Now we mash for an hour. The pump recirculates liquid through the grain. Enzymes (alpha and beta amylase) in malted barley convert starches into sugars (maltose and glucose). Each enzyme has different but overlapping ideal temp ranges to convert starch, both are active at 68C.

Show thread

While I wait for the mash to complete, I take notes in a notebook I've used for years to track my brewing. This makes it easier to repeat beers I like, and review my notes if something doesn't work out.

Show thread

Halfway through the mash you can see the effect of recirculating liquid through the grain. The husks and perforated bottom are filtering as they should and the cloudy liquid from 30 minutes ago is much clearer.

Show thread

One the mash completes, we start the "mash out" step. This heats what we can officially call "wort" (pre-beer or sugary barley liquid) up to 75C to denature the enzymes and stop the creation of any more sugars. This also makes it easier to rinse out more sugar in the next step.

Show thread

Now we "sparge" or rinse the remaining sugar out of the grain with 10L of 75C water in 1L batches from my electric kettle. The internal grain basket lifts out and rests on top of the kettle so wort and sparge water can drain into the boil kettle that is heating up to 98C.

Show thread

The boil! This recipe calls for a 90min boil but most are 60 mins. We boil wort for a few reasons:
1. Cooking. Maillard reactions develop flavor in the wort
2. Sterilization. Wort is sticky, sugary stuff. Boiling kills microorganisms in the barley that'd infect the beer.

Show thread

3. Boiling coagulates protein solids out of solution you don't want in the beer.
4. Boil off other compounds you don't want into the air. This boil is 90mins in particular to give more time to boil off di-methyl sulfide (DMS) in the wort.
5. Bittering with hops (next step).

Show thread

Adding hops with 60 mins left in the boil. Hops boiled this long produce a bitter flavor and are called "bittering hops". Originally hops were added because it extracts an antibiotic oil, lupulin, which helps prevent infection in the beer, particularly before alcohol is present.

Show thread

Cleaning part 1! While we wait for the boil to finish it's a great time to clean up equipment we aren't using for the rest of the process.

Show thread

Ten minutes before the end of the boil I connect my counterflow chiller to the pump and recirculate boiling wort through it. Up to now we haven't been concerned with sterilization but after the boil everything the wort touches must be sterile including inside this chiller.

Show thread

We must cool the wort to room temp so we don't kill the yeast we add later. The Grainfather comes w/ a counterflow chiller that makes this fast. Pump hot wort through 1 tube, cool water the other. Heat exchanges inside, cool wort goes back to the kettle, hot water to a bucket.

How do I know when the wort is cool? I have an inline thermometer connected to the wort output on the counterflow chiller.

Show thread

Now that it's cool, I move the counterflow output to my fermentation vessel (a keg) and let the pump transfer it. The keg was sterilized with iodophor solution and the exhaust water from the counterflow chiller. Fun fact: iodophor is on the official list of coronavirus killers!

Show thread

Once the fermenter is almost full, I pitch the yeast. I also sprayed the outside of the yeast container with sanitizing solution about 10 minutes before I opened it so the outside was sterile.

Show thread

This is a lager so I will ferment it at celler temperatures in a warm fridge (~10C). I have attached a tube to the keg inlet so CO2 the yeast exhausts will bubble out in a jar of sanitizing solution. It takes ~ a month to ferment, another month lagering before ready.

Show thread

While pumping out the wort to the fermenter, I also collected some so I could do a gravity measurement. This tells me how much sugar is in the solution compared to water. Strangely this is *much* lower (1.060) than what I was expecting (1.073!). Many reasons why this could be:

Show thread

1. Overestimated amount of water that would boil off (likely).
2. Mash not efficient (unlikely, my Grainfather mashes are usually *too* efficient).
3. Grains in the recipe slightly different from what was available to put in the calculator.

Show thread

All that's left is cleaning part 2 and this is where the Grainfather shines. First I dump and rinse the kettle and give it a quick wipe with a rag. Then I fill it with 12L of water and PBW cleaning solution, heat it up to 60C and recirculate 10 mins. Dump, repeat w/ clean water.

Show thread

If you made it this far, thank you! Live posting this felt kind of like having you here with me in while I brewed during lockdown. Also thanks to Grainfather for making my brew day so much simpler and about 2 hours faster!

Show thread

@kyle Thanks for sharing! That was cool to read about but wow, the level of dedication required.

@leimon You can get pre-made kits that use dried or liquid malt extract and completely skip a lot of this process and start at the boil. It's how I got started and what I recommend for everyone who wants to try it out.

@kyle Thanks for sharing. I brewed once with one of those starter kits in a plastic bucket. The beer was ok ;)
I guess yours will be outstanding.

@kyle if you get a chance, consider getting something like this. I found it to be a useful and inexpensive upgrade. Wastes less wort & easier to read.

amazon.com/Anpro-Refractometer

@keverets It's been on my wishlist for some time, just haven't gotten around to getting one yet.

@kyle interesting. Never fermented in keg (have used buckets but usually use glass carboys). Some get extra active like Belgian Quads, so having a blow-off tube option is handy.

@keverets Kegs have some nice properties. You can get trub and yeast off the bottom my pressurized a bit and using a picnic tap. Can also transfer to a different keg with a bit of pressure without exposing to outside air.

Sign in to participate in the conversation
Librem Social

Librem Social is an opt-in public network. Messages are shared under Creative Commons BY-SA 4.0 license terms. Policy.

Stay safe. Please abide by our code of conduct.

(Source code)

image/svg+xml Librem Chat image/svg+xml